Help me! Error"Internal error in boundary respecting."

Thread index  |  Previous thread  |  Next thread  |  Start a new discussion

RSS FeedRSS feed   |   Email notificationsTurn on email notifications   |   7 Replies   Last post: August 28, 2013 4:07am UTC
Vinh Nguyen Van

Vinh Nguyen Van

August 18, 2013 9:37am UTC

Help me! Error"Internal error in boundary respecting."

Hi, all
I want fix it, It is coordinate (-2,06378, 1,35209, 2,8034)
Thank a lot
Vinh Nguyen

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Fabio Greco

Fabio Greco

August 20, 2013 11:18am UTC in response to Vinh Nguyen Van

Re: Help me! Error"Internal error in boundary respecting."

Hi,

try to take a look at this thread www.comsol.com/community/forums/general/thread/1355/
Could you solve your problem?

Regards

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Vinh Nguyen Van

Vinh Nguyen Van

August 27, 2013 9:47am UTC in response to Fabio Greco

Re: Help me! Error"Internal error in boundary respecting."

Thank a lot, I am using Solidwork to design. I feel work in it happen lots of error. If I use autocad 3D, I will control error better ?

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Fabio Greco

Fabio Greco

August 27, 2013 10:00am UTC in response to Vinh Nguyen Van

Re: Help me! Error"Internal error in boundary respecting."

Hi,

actually I don't know because I usually build my geometry directly on Comsol. Try to browse in the forum. I edited your post adding the filters "Geometry" and "LiveLink Products", maybe some users can give you useful advices!

Bests

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Vinh Nguyen Van

Vinh Nguyen Van

August 27, 2013 10:22am UTC in response to Fabio Greco

Re: Help me! Error"Internal error in boundary respecting."

thanks Fabio Greco
I design win turbine blade, so the design direct it is difficult. You can help me provide some one documents about drawing direct on COMSOL.
look forward to receiving feedback from you

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Fabio Greco

Fabio Greco

August 27, 2013 10:54am UTC in response to Vinh Nguyen Van

Re: Help me! Error"Internal error in boundary respecting."

Hi,

I think it's an an hard challenge to model a wind turbine blade directly in Comsol, and it may be even impossible! Importing the geometry into Comsol through SolidWorks or others is the most wise approach!

Regards

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Toyin Aseeperi

Toyin Aseeperi

August 27, 2013 6:27pm UTC in response to Fabio Greco

Re: Help me! Error"Internal error in boundary respecting."

Hi,
I have also had similar challenges when trying to mesh thin slices of materials present in a domain. I will appreciate if anyone has a solution approach to meshing these geometries in COMSOL.
I am attaching a copy of my geometry and model here.

Attachments:   TestModel6b.mph  

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse

Vinh Nguyen Van

Vinh Nguyen Van

August 28, 2013 4:07am UTC in response to Toyin Aseeperi

Re: Help me! Error"Internal error code: 900."

I get this error when importing from solid to COMSOL. Everyone help me!

Reply  |  Reply with Quote  |  Send private message  |  Report Abuse


Rules and guidelines