COMSOL Derived Universal Scaling Model For Low Reynolds Number Viscous Flow Through Microfabricated Pillars – Applications to Heat Pipe Technology
N. Srivastava, and C.D. Meinhart
Department of Mechanical Engineering, University of California Santa Barbara, Santa Barbara California, USA
Cooling of high-power density electronic devices remains a challenge. Microfluidic heat-pipes with the potential of achieving ultra-high thermal conductivities offer a low-cost technology for cooling electronics. To achieve high thermal conductivity, it is critical to maximize the rate of liquid transport inside the heat pipe. We propose a novel array of microfabricated pillars to maximize liquid ...
Finite Element Analysis of an Enzymatic Biofuel Cell: The Orientations of a chip inside a blood artery
C. Wang, Y. Parikh, Y. Song, and J. Yang
Mechanical & Materials Science Engineering, Florida International University, Miami, Florida, USA
Output performance of an implantable enzymatic biofuel cell (EBFC) with three- dimensional highly dense micro-electrode arrays has been simulated with a finite element analysis approach. The purpose of this research is to optimize the orientation of this EBFC chip inside a blood artery such that the mass transport of glucose around all the micro-electrodes can be improved and hence output ...
H. Ishimori, K. Endo, and M. Yamada
National Institute for Environmental Studies, Tsukuba, Ibaraki, Japan
In this study, COMSOL Multiphysics was used for the reliability evaluation for static chamber method at landfill sites. Static chamber method, which measures landfill gas emission fluxes, is widely used at landfill sites for the monitoring of greenhouse gas emission such as methane and carbon dioxide. The accuracy and the reliability of static chamber method are dependent on the measuring ...
J. Biggs, P. VonLockette, and S. Lofland
Rowan University, Glassboro, New Jersey
Magnetorheological Elastomers (MREs) are a composite that consist of magnetic micrometer sized particles suspended within rubber matrix filler. By placing this material within an external magnetic field during the rubber curing process, the poles of the particles are forced to align and form chains of particles within the matrix. These chains cause the MRE to change its stiffness properties when ...
Viscous damping of a periodic perforated MEMS microstructure when the Reynolds’ equation cannot be applied: Numerical simulations
D. Homentcovschi, and R.N. Miles
Department of Mechanical Engineering, SUNY Binghamton, NY
This paper develops a computational model for determining the total damping coefficient for a unit cell of a MEMS microscale device containing a repetitive pattern of holes. The basic cell of the microstructure is approximated by an axi-symmetric domain and the velocity and pressure fields are determined from solutions of the Navier-Stokes equations using the finite element software package ...
Department of Mechanical Engineering, University of Washington, Seattle, Washington, USA
Heat conduction through a slab, 0 ≤ x ≤ W is one dimensional. However, if one of the edges, say x=0, is rough the conduction will be two dimensional. The two dimensionality varies with the correlation length with a maximum at a length approximately 10% of the slab width. The maximum percentage standard deviation of the flux is of the order of 3 time that of the roughness. Monte ...
C.B. Crawford, Y. Shin, and G. Porter
Department of Physics and Astronomy, University of Kentucky, Lexington, Kentucky, USA
Traditionally the design cycle for magnetic fields involves guessing at a reasonable conductor / magnetic material configuration, using FEA software to calculate the resulting field, modifying the configuration, and iterating to produce the desired field. Our method involved solving the classical Laplace equation on regions with imposed boundary conditions, which was implemented straightforwardly ...
Y. Huang, and A. Mason
Electrical and Computer Engineering, Michigan State University, East Lansing, Michigan, USA
This paper describes the modeling of an electrochemical biosensor embedded in a microfluidic channel to determine the concentration of a target biomolecule. The total amount of analyte in the sample can be calculated by integrating the analyte concentration over the duration of the peak current. The biosensor is constructed by immobilizing redox-enzyme on an interdigitated array (IDA) electrode ...
C. Bouchot, and M.A. Valenzuela
Instituto Politécnico Nacional-ESIQIE, México D.F, México
A general purpose stainless steel micro reactor setup for methane conversion is being designed for research purposes. We intend to design and build a modular device that would be able to manage different types of reactions depending on the installed modules. The device should be able to allow the study of gas phase reactions at low (atmospheric) and high pressures (up to 20 MPa), with the ...